Analytical Solution of Heat Exchanger Tubesheet Deformation Under Temperature Load
-
摘要: 根据换热器结构形式建立了用于计算管板变形的力学模型,参考ASME Ⅷ1计算管板的有效弹性常数,并将外筒和换热管束分别等效为会因温度和压力载荷产生轴向变形的弹簧和弹性基础.应用Ritz法建立了管板挠度的解析解,将该解析解与三个不同规模换热器的有限元分析结果进行对比.结果表明,建立的解析解与有限元分析结果吻合良好,验证了推导的管板变形解析解的正确性.研究结果对固定管板式换热器的设计有较大的指导意义.Abstract: A mechanical model for calculating tubesheet deformation was established according to the structure of the heat exchanger. The effective elastic constant of the tubesheet was calculated with reference to code ASME Ⅷ-1, the outer cylinder and the heat exchange tube bundle were respectively equalized to springs and elastic foundations axially deforming due to temperature and pressure loads. An analytical solution of tubesheet deflection was obtained with the Ritz method, and compared with the numerical simulation results of 3 heat exchangers of different scales. The results show that, the analytical solution is in good agreement with the numerical simulation results, which verifies the correctness of the derived analytical solution of tubesheet deformation. The research work has guiding significance for the design of fixed tubesheet heat exchangers.
-
[1] GARDNER K A. Heat-exchanger tube-sheet design[J]. Journal of Applied Mechanics,1948,70: 377-385. [2] SLOT T, O’DONNELL W J. Effective elastic constants for thick perforated plates with square and triangular penetration patterns[J]. Journal of Engineering for Industry,1971,93(4): 935-942. [3] O’DONNELL W J. Effective elastic constants for the bending of thin perforated plates with triangular and square penetration patterns[J]. Journal of Engineering for Industry,1973,95(1): 121-128. [4] 钱伟长, 戴福隆. 厚管板的等效弹性常数[J]. 力学学报, 1981,17(4): 364-371.(CHIEN Weizang, DAI Fulong. Effective elastic constants for thick perforated plates[J]. Chinese Journal of Theoretical and Applied Mechanics,1981,17(4): 364-371.(in Chinese)) [5] 龚明明, 虞斌, 郝彪. 复杂工况下薄管板换热器的安全评定[J]. 轻工机械, 2013,31(6): 104-107, 114.(GONG Mingming, YU Bin, HAO Biao. Stress analysis of thin tube sheet heat exchanger subjected to complex loads[J]. Light Industry Machinery,2013,〖STHZ〗 31(6): 104-107, 114.(in Chinese)) [6] 张贤福, 刘丰, 孙志刚, 等. 固定管板管壳式换热器瞬态热应力分析[J]. 压力容器, 2016,33(5): 34-38, 80.(ZHANG Xianfu, LIU Feng, SUN Zhigang, et al. Transient thermal stress analysis of fixed tubesheet heat exchanger[J]. Pressure Vessel Technology,2016,33(5): 34-38, 80.(in Chinese)) [7] 高程, 张丹, 张玉明, 等. 预冷器在水压试验中管板严重变形原因[J]. 计算机辅助工程, 2018,27(2): 36-42.(GAO Cheng, ZHANG Dan, ZHANG Yuming, et al. Cause of serious deformation of precooler tube-sheet in hydraulic test[J]. Computer Aided Engineering,2018,27(2): 36-42.(in Chinese)) [8] 中华人民共和国国家质量监督检验检疫总局, 中国国家标准化管理委员会. 热交换器: GB/T 151—2014[S]. 2014.(General Administration of Quality Supervision, Inspection and Quarantine of the People’s Republic of China, Standardization Administration of the People’s Republic of China. Heat exchangers: GB/T 151—2014[S]. 2014.(in Chinese)) [9] 邹广平, 何蕴增, 张晓威, 等. 文克勒地基上圆形薄板受轴对称载荷作用的贝塞尔函数解[J]. 哈尔滨船舶工程学院学报, 1993,14(4): 105-110.(ZOU Guangping, HE Yunzeng, ZHANG Xiaowei, et al. Bessel function solution of circular thin slab under axially symmetrical load on Winkler foundation[J]. Journal of Harbin Shipbuliding Engineering Instiute,1993,〖STHZ〗 14(4): 105-110.(in Chinese)) [10] 冯文杰, 刘金喜. 文克勒地基上夹支圆板轴对称弯曲问题的Fourier-Bessel级数解[J]. 石家庄铁道学院学报, 1995,8(1): 70-74.(FENG Wenjie, LIU Jinxi. Fourler-bessel sewies solution of the axisymmetrical bending of circular clamped plates on Winkler foundations[J]. Journal of Shijiazhuang Railway Institute,1995,〖STHZ〗 8(1): 70-74.(in Chinese)) [11] 徐芝纶. 弹性力学: 下册[M]. 北京: 高等教育出版社, 1992.(XU Zhilun. Elasticity: Vol 2 [M]. Beijing: Higher Education Press, 1992.(in Chinese)) [12] 俞佐平. 传热学[M]. 北京: 高等教育出版社, 1988.(YU Zuoping. Heat Transfer [M]. Beijing: Higher Education Press, 1988.(in Chinese)) [13] 王光钦. 弹性力学[M]. 北京: 中国铁道出版社, 2008.(WANG Guangqin. Elasticity [M]. Beijing: China Railway Press, 2008.(in Chinese)) [14] MILLER U R, PASTOR T P. Section Ⅷ, division 1: rules for construction of pressure vessels[Z]//Companion guide to the ASEM boiler & pressure vessel code. 2017. [15] 中华人民共和国国家质量监督检验检疫总局, 中国国家标准化管理委员会. 压力容器 第2部分: 材料: GB 150.2—2011[S]. 2011.(General Administration of Quality Supervision, Inspection and Quarantine of the People’s Republic of China, Standardization Administration of the People’s Republic of China. Pressure vessels, part 2: materials: GB 150.2—2011[S]. 2011.(in Chinese)) [16] 钢制压力容器: 分析设计标准: JB 4732—1995[S]. 2005.(Steel pressure vessels: design by analysis: JB 4732—1995[S]. 2005.(in Chinese))
点击查看大图
计量
- 文章访问数: 811
- HTML全文浏览量: 211
- PDF下载量: 352
- 被引次数: 0