A Simplified Load Analysis Method and Load Characteristics of Coated Turbine Blades

LIU Linchuan; HOU Cheng; FAN Xueling; ZHOU Ziyang

doi:10.21656/1000-0887.460201

Volume 47 Issue 6

Jun. 2026

Turn off MathJax

Article Contents

Article Navigation > Applied Mathematics and Mechanics > 2026 > 47(6): 723-735

LIU Linchuan, HOU Cheng, FAN Xueling, ZHOU Ziyang. A Simplified Load Analysis Method and Load Characteristics of Coated Turbine Blades[J]. Applied Mathematics and Mechanics, 2026, 47(6): 723-735. doi: 10.21656/1000-0887.460201

Citation:

PDF( 6961 KB)

A Simplified Load Analysis Method and Load Characteristics of Coated Turbine Blades

doi: 10.21656/1000-0887.460201

Xi’an Key Laboratory of Extreme Environmental and Protection Technologies, School of Aerospace Engineering, Xi’an Jiaotong University, Xi’an 710049, P.R. China

Received Date: 2025-11-14
Rev Recd Date: 2026-03-13

Available Online: 2026-07-03

Publish Date: 2026-06-01

Abstract

Abstract

To address the challenges of complex modeling and low efficiency in load analysis of coated turbine blades with cross-scale multilayer coating-substrate systems, an efficient load analysis method based on a shell conduction model and a simplified mechanical model was proposed. The equivalent thermal resistance was introduced into the temperature analysis, and the consistency relation of the interfacial total strain tensors was established in the mechanical modeling, to effectively avoid mesh proliferation, distortion, and computational divergence induced by cross-scale interfaces. The results indicate that, compared with the conventional explicit modeling method, the proposed approach improves the minimum Jacobian ratio by approximately 51.9%, reduces the number of elements by about 80.8%, and enhances computational efficiency by more than an order of magnitude, while keeping temperature and mechanical load prediction errors below 5%. Furthermore, the analysis of coated turbine blades shows that, temperature hotspots are concentrated at the blade tip, while mechanical load hotspots are mainly distributed at the leading edge of the blade root. The load distribution in the coating exhibits a trend highly consistent with that of the substrate, reflecting a strongly coupled response behavior.
- coated turbine blade,
- thermo-mechanical load,
- finite element simulation,
- shell conduction model,
- simplified mechanical model

FullText(HTML)

References(34)

References

[2]王铁军, 范学领, 丁秉钧, 等.热障涂层强度理论与检测技术[M]. 西安: 西安交通大学出版社, 2016. (WANG Tiejun, FAN Xueling, DING Bingjun, et al.Strength Theory and Testing Technology of Thermal Barrier Coatings[M]. Xi’an: Xi’an Jiaotong University Press, 2016. (in Chinese))

PADTURE N P, GELL M, JORDAN E H. Thermal barrier coatings for gas-turbine engine applications[J].Science,2002,296(5566): 280-284.

[3]LIU L, FU S, HU Z, et al. Thermo-mechanical analysis of TBC-film cooling system under high blowing ratio considering the effects of curvature[J].Surface and Coatings Technology,2023,470: 129826.

[4]柴怡君, 林晨, 李跃明. 考虑化学氧化效应时热障涂层氧化物的生长规律[J]. 应用数学和力学, 2015,36(4): 404-413. (CHAI Yijun, LIN Chen, LI Yueming. Growth trend of thermal grown oxide in TBCs under chemical oxidation effect[J].Applied Mathematics and Mechanics,2015,36(4): 404-413. (in Chinese))

[5]LIU L, WU J, HU Z, et al. Thermal analysis of turbine blades with thermal barrier coatings using virtual wall thickness method[J].Computer Modeling in Engineering & Sciences,2023,134(2): 1219-1236.

[6]WANG X M, HUI Y Z, HOU Y Y, et al. Direct investigation on high temperature tensile and creep behavior at different regions of directional solidified cast turbine blades[J].Mechanics of Materials,2019,136: 103068.

[7]RANI S, AGRAWAL A K, RASTOGI V. Failure analysis of a first stage IN738 gas turbine blade tip cracking in a thermal power plant[J].Case Studies in Engineering Failure Analysis,2017,8: 1-10.

[8]CHUNG H, SOHN H S, PARK J S, et al. Thermo-structural analysis of cracks on gas turbine vane segment having multiple airfoils[J].Energy,2017,118: 1275-1285.

[9]QU S, FU C M, DONG C, et al. Failure analysis of the 1st stage blades in gas turbine engine[J].Engineering Failure Analysis,2013,32: 292-303.

[10]KARGARNEJAD S, DJAVANROODI F. Failure assessment of Nimonic 80A gas turbine blade[J].Engineering Failure Analysis,2012,26: 211-219.

[11]WANG L, LI D C, YANG J S, et al. Modeling of thermal properties and failure of thermal barrier coatings with the use of finite element methods: a review[J].Journal of the European Ceramic Society,2016,36(6): 1313-1331.

[12]WANG Z, WANG D, LIU Z, et al. Numerical analysis on effects of inlet pressure and temperature non-uniformities on aero-thermal performance of a HP turbine[J].International Journal of Heat and Mass Transfer,2017,104: 83-97.

[13]MAIKELL J, BOGARD D, PIGGUSH J, et al. Experimental simulation of a film cooled turbine blade leading edge including thermal barrier coating effects[J].Journal of Turbomachinery,2011,133: 011014.

[14]LV B, JIN X, CAO J, et al. Advances in numerical modeling of environmental barrier coating systems for gas turbines[J].Journal of the European Ceramic Society,2020,40(9): 3363-3379.

[15]ZHU W, WANG J W, YANG L, et al. Modeling and simulation of the temperature and stress fields in a 3D turbine blade coated with thermal barrier coatings[J].Surface and Coatings Technology,2017,315: 443-453.

[16]JI Y, MA C, GE B, et al. Conjugate heat transfer investigation on the cooling performance of air cooled turbine blade with thermal barrier coating[J].Journal of Thermal Science,2016,25(4): 325-335.

[17]SHEN Q, LI S Z, YANG L, et al. Coupled mechanical-oxidation modeling during oxidation of thermal barrier coatings[J].Computational Materials Science,2018,154: 538-546.

[18]SONG J, QI H, SHI D, et al. Effect of non-uniform growth of TGO layer on cracking behaviors in thermal barrier coatings: a numerical study[J].Surface and Coatings Technology,2019,370: 113-124.

[19]ZHU W, CAI M, YANG L, et al. The effect of morphology of thermally grown oxide on the stress field in a turbine blade with thermal barrier coatings[J].Surface & Coatings Technology,2015,276: 160-167.

[20]LI B, FAN X, LI D, et al. Design of thermal barrier coatings thickness for gas turbine blade based on finite element analysis[J].Mathematical Problems in Engineering,2017,2017(1): 2147830.

[21]VO D T, MAI T D, KIM B, et al. Numerical study on the influence of coolant temperature, pressure, and thermal barrier coating thickness on heat transfer in high-pressure blades[J].International Journal of Heat and Mass Transfer,2022,189: 122715.

[22]BALINT D, HUTCHINSON J. An analytical model of rumpling in thermal barrier coatings[J].Journal of the Mechanics and Physics of Solids,2005,53(4): 949-973.

[23]BALINT D S, KIM S S, LIU Y F, et al. Anisotropic TGO rumpling in EB-PVD thermal barrier coatings under in-phase thermomechanical loading[J].Acta Materialia,2011,59(6): 2544-2555.

[24]JIANG J, MA X, WANG B. Stress analysis of the thermal barrier coating system near a cooling hole considering the free-edge effect[J].Ceramics International,2020,46(1): 331-342.

[25]VAUNOIS J R, DORVAUX J M, KANOUT P, et al. A new version of a rumpling predictive model in thermal barrier coatings[J].European Journal of Mechanics A,2013,42: 402-421.

[26]DRYEPONDT S, PORTER J R, CLARKE D R. On the initiation of cyclic oxidation-induced rumpling of platinum-modified nickel aluminide coatings[J].Acta Materialia,2009,57(6): 1717-1723.

[27]TOLPYGO V, CLARKE D. On the rumpling mechanism in nickel-aluminide coatings, part Ⅱ: characterization of surface undulations and bond coat swelling[J].Acta Materialia,2004,52(17): 5129-5141.

[28]SMETANKINA N V, POSTNYI O V, MERKULOVA A I, et al. Modeling of non-stationary temperature fields in multilayer shells with film heat sources[C]//2020 IEEE KhPI Week on Advanced Technology (KhPI Week). Kharkiv, Ukraine: IEEE, 2020: 242-246.

[29]BERGMAN T.Fundamentals of Heat and Mass Transfer[M]. Hoboken: John Wiley & Sons, 2011.

[30]LIU L, FAN X, CHU Z, et al. Thermo-mechanical loads and creep life assessment for coated turbine blades considering the influence of cooling hole blockage[J].Engineering Failure Analysis,2025,170: 109321.

[31]TRAEGER F, VAEN R, RAUWALD K H, et al. Thermal cycling setup for testing thermal barrier coatings[J].Advanced Engineering Materials,2003,5(6): 429-432.

[32]EVANS H E. Oxidation failure of TBC systems: an assessment of mechanisms[J].Surface and Coatings Technology,2011,206(7): 1512-1521.

[33]中国金属学会高温材料分会. 中国高温合金手册[M]. 北京: 中国标准出版社, 2012. (The High Temperature Materials Branch of The Chinese Society for Metals.China Superalloys Handbook[M]. Beijing: Standards Press of China, 2012. (in Chinese))

[34]CAI L, HE Y, WANG S, et al. Thermal-fluid-solid coupling analysis on the temperature and thermal stress field of a nickel-base superalloy turbine blade[J].Materials,2021,14(12): 3315.

Relative Articles

Supplements(0)

Cited By

Proportional views