An Estimation Method of Bearing Strength of Bolted Joints in Fibre Reinforced Composite

Yang Ling

Article Contents

Article Navigation > Applied Mathematics and Mechanics > 1986 > 7(1): 95-101

Yang Ling. An Estimation Method of Bearing Strength of Bolted Joints in Fibre Reinforced Composite[J]. Applied Mathematics and Mechanics, 1986, 7(1): 95-101.

Citation:

Yang Ling. An Estimation Method of Bearing Strength of Bolted Joints in Fibre Reinforced Composite[J]. Applied Mathematics and Mechanics, 1986, 7(1): 95-101.

Citation:

Yang Ling. An Estimation Method of Bearing Strength of Bolted Joints in Fibre Reinforced Composite[J]. Applied Mathematics and Mechanics, 1986, 7(1): 95-101.

PDF( 444 KB)

An Estimation Method of Bearing Strength of Bolted Joints in Fibre Reinforced Composite

Yang Ling

Department of Aircraft Engineering Northivestern Polytechnical University, Xi'an

Received Date: 1983-05-03
Publish Date: 1986-01-15

Abstract

Abstract

Some researchers have estimated the strength of bolted joints in fibre reinforced composite, using simple and efficient engineering procedures. However, for these procedures the effect of clamping due to the strength of bolted joints is not considered. In this paper, a method is presented for predicating critical bearing strength of single-hole bolted joints in composite on the basis of observing and analysing the results of experiments. The clamping effect of bolts is considered. The calculated results correspond to the test data on Glaphic/Epoxy laminates.

FullText(HTML)

References(16)

References

[1]	羊姈,复合材料螺栓连接设计,西工大科研资料SHJ 8056期,(1980).
[2]	Waszezak,J.P.and T.A.Cruse.Failure mode and strength prediction of anisotropic bolt bearing specimens,J of Composite Materials,5(1971),421.
[3]	Jong,Theo.De., Stresses around pin-loaded holes in elastically orthotropic or isotropic plates,J.Composite Materials.2(1977),313.
[4]	Eisenmann,J.R.,Bolted joint static strength model for composite materials,NASA-TM-X-3377(1976).
[5]	Hart-Smith,L.J.,Bolted joints in graphite epoxy composites.Douglas Aircraft Company,NASA Contract Report,No NASA CR-144899(1976).
[6]	Collings,T.A.,The strength of bolted joints in multidirectional CFRP laminates,Composites.8(1977).
[7]	Quinn,W.J and F.L.Matthews,The effect of stacking Sequence on the pin-bearing strength in glass fibre reinforced plastic,J Cmposite Materials.2(1977),139.
[8]	Kim,R.Y and J.M.Whitney,Effect of temperature and moisture on pin bearing strength of composite laminates,J Composite Materials.10(1976),149.
[9]	Wilson.D.W and R B.Pipes.Analysis of the shearout failure mode in composite bolted joints,Composite Structure.p 34.
[10]	Tang,S.,Failare of composite joint under combined tension and bolt loads.J Composite Materials.15(1981),329.
[11]	Soui,S.R.,Failure analysis of composite laminates with a fastener hole.Joining of Composite Material.p.145.
[12]	Soni.S.R.,Stress and strength analysis of bolted joints in composite laminates,Composite structure,p.50.
[13]	吴金泉,碳纤维/环氧树脂复合材料迭层板螺栓接头强度试验及应力集中统数的研究,航空工业部625所.
[14]	陈绍傑等,复合材料连接试验报告,航空工业部601所.
[15]	杨炳章等,碳纤维/环氧复合材料迭层板挤压强度的实验研究,西工大科技资料SHJ 8489期,(1982).
[16]	羊姈,碳纤维复合材料迭层平板孔边应力分析,西工大科技资料SHJ 8217期,(1982).